![]() where water curing is inconvenient or potable water for curing is not available, sealing fresh concrete surface with curing compound is the best alternate curing method.concrete curing compound will effectively prevent evaporation of water from concrete, provided it is not puctured or damaged, but will not allow the ingress of water to replenish that is lost by self dessication.tile adhesives based on the above polymers.water based emulsion paint systems containing PVA, PVC, and acrylic co-polymers.Polycure AC acts as a primer and bonding agents for the following systems: for highly porous surfaces, a second coat has to be applied at the same coverage rate. The application can be done by a brush, roller or an airless spray at a coverage rate of 5m²/l. In case of de-shuttering, the concrete surface is wetted with water but not with free standing water, before the curing compound is applied. The particles are suspended in water, then as the paint dries the. ApplicationĪpplied immediately after the initial bleed water evaporates and the concrete has achieved its initial set. Emulsion paint consists of tiny polymer particles within which the pigments are trapped. We remind you that the growth of algae or mold can be a purification problem.Mix the contents of the drum thoroughly prior to the application in order to remove the sediments. It is recommended to allow at least 15 days to elapse before filling the pool. The Thinner for water-based paints and enamels, leaving 6 hours between coats. Uses Different Types Emulsion Paint Application Step 1) Prep Step 2) Paint Step 3) Let the Surface Dry Step 4) Apply the Second Coat How to Remove Emulsion Paint Do You Need to Thicken Emulsion Paint Emulsion vs. Apply two coats of Piscinas al Agua to the use or diluting a maximum of 5% with One time prepared, apply the Water-based Epoxy Primer diluted 30% with the Diluent for water-based paints and enamels. The surface must be prepared properly, sand the area to be prepared and leave it free of dust, clean and dry. If alkalinity is detected on the support, must correct. For this it must paint a small non-visible area, let it dry for two weeks and try scraping or scratching to see if the adhesion is adequate. The formulation of these paints is discussed in the sections below. They have different types, including emulsion, acrylic, latex, polyvinyl acetate (PVA), and silicone. Wash and sand lightly, putty if necessary and apply afterwards. In addition, an adhesion test is recommended to ensure material compatibility. Water-based Paints As the name suggests, water-based paints use almost all water as a solvent. As an alternative, it you could apply a first coat of Water-Based Paint diluted 25% with Thinner for water-based paints and enamels. Wait 8 hours to repaint.Īpply two coats of Piscinas al Agua directly after use or diluting a maximum of 5% with our Diluent for water-based paints and enamels, leaving 6 hours to dry between coats. For this, a first layer of Sellacryl diluted with Thinner for water-based paints and enamels in a 4:1 ratio, respectively. Once the surface is prepared, we will begin by priming the support. ![]() Rinse with plenty of water to neutral pH.ģ. ![]() ![]() Apply salfumán or diluted acids 10-15% in water and leave to act for 15 minutes.Ģ. If there are traces of dirt or the pore has to be opened, whether it is a new surface or not, proceed with the Following way:ġ. Before proceeding with painting, the support must be free of damp, clean, dry and without the presence of rust, grease or salt. The surface must be porous and the lime milk must be removed from the setting. Modo de empleo:Īllow at least 30 days to elapse before being painted for complete setting. In pools with tiles or mosaic, it can be used if we use the Water-based epoxy primer as a bonding bridge of two components. Specially formulated for cement or concrete pools due to its special resistance to water, alkalis and acids.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |